|
| |
TARGET
Concrete Chain Saws - Cut Off Saws - Pipe Saw - Demolition Saw -
Walk Behind Saws - Diamond Blades - Core Bits - Abrasives
|
BACK
Accessories/ Diamond Chains / Bars |
|
Blue
Gator - Gas Powered Concrete Chain Saw |
 |
Bar and Chain Not Included |
|
New 6.2 cu. inch (101cc)
engine designed specifically for wet cutting concrete and an
abrasive environment.
Special crankshaft sealing and air filtration. |
|
Sprocket side cover and guard
flap designed for maximum operator safety |
|
Patented WallWalker®
helps ensure easier, straighter cuts in multiple positions.
|
|
Easy access and simple
maintenance requirements |
|
New Target MP diamond chain
and cutting system designed for unique demands and vibration
of a gas powered source. |
|
Lightweight magnesium
castings. |
|
Gas Powered Concrete Chain Saw |
|
|
Blue
Gator Gas Powered Chain Saw |
6
1/2 |
5500
fpm (28 m/s) |
14 |
27.50 |
|
Specifications
- Blue Gator - Gas Powered Concrete Chain Saw |
| 2-Stroke Single Cylinder Air
Cooled |
| 6.2 cu. in (10cc) |
| 6 1/2 HP @ 8500 RPM |
| 11,500 + 500 RPM, Mechanically
governed 2500 - 2800 RPM idle |
| 5500 fpm ( 28 m/s ), free
running |
| 27 1/2 lbs. (12.5 kg) |
| 11 or 14" (28 or 36 cm) |
| 23 in. (58cm) Length |
| 14 in. (36cm) Height |
| 12 in. (30cm) Width |
| Walbro WGAH#, Throttle shaft
sealed |
| Dust and water shield |
| Special water resistant
electronic ignition |
| Three-weight, single stroke,
water and concrete proofed |
| 25:1 gasoline-to-oil |
| 0.26 gal (1 liter) 15 - 18
minute tank, continuous full load operation |
| 80 psi (6 bar) recommended;
3.5 gpm (13 liters/min) minimum |
| 102 dBA @ 1 meter |
| 8 meters/sec2 (front handle) |
Hard aggressive and steel:
15-25 in 2min (90-160 cm2/min)
Medium aggregates: 20-30 in 2/min (160-190 cm2/min)
Masonry Brick, Block: 30-5- in2/min (190-320 cm2/min) |
|
Blue
Gator - Hydraulic Powered Concrete Chain Saw |
|
|
|
Blue
Gator Hydraulic Saws |
2,500
psi |
4950
fpm (25 m/s) |
13 |
15.00 |
|
Specifications
- Blue Gator - Hydraulic Powered Concrete Chain Saw |
| 8gpm (30 liters/min)* |
| 2,500 psi (175.5 bar)* |
| Open center |
| 4950fpm (25 m/s), free running |
| 16 lbs (6.8 kg) |
| 13 inches (33 cm) |
| 18 inches (46 cm) Length |
| 10 inches (25 cm) Height |
| 8 inches (20 cm) Width |
| 8 tooth high-alloy spur w/16mm
trantorgue® |
| HTMA 1/2 inch Flush-Face |
| 18 inch length, 3/8 inch
diameter, 2,500 psi working pressure |
| 88 dBA @ 1 meter |
| 3,5 meter/sec.2 (front handle) |
* Can be used with higher flow systems ONLY with flow
adapter (Target part number 180392), 30 gpm max.
|
|
